BMC Tactical - Warrior Steel LLC » walter

Coming Soon- 5.11 Clearance

walter — Wed, 01 Feb 2012 05:17:47 +0000

Look for it in the next few days.

Thank you,

BMC Tactical / Warrior Steel LLC
2617 Coors Blvd SW, Albuquerque, NM 87121
View the map of our location here

Silencerco 45 OSPREY

walter — Fri, 27 Jan 2012 03:36:18 +0000

I personally have one and they are fantastic!

“With the modern combat handgun in mind, Silencerco set out to create a silencer that performs well and looks like it belongs—the best possible marriage between host weapon and silencer. Silencerco went to work to make a suppressor that maximizes sound suppression levels, allows the use of more host pistols with factory sights, and has more operationally friendly features. What was created was the Osprey pistol silencer available for 9mm, .40 S&W, and 45ACP.

The Osprey is an eccentric silencer, which means that the bore does not run down the middle of the tube.

Although round silencers are very effective for many applications, for a centerfire handgun round it has its limits. To obtain the most suppression, silencers must have as much internal volume as possible; but for a round tubular silencer, the only way to acquire more internal volume is by increasing the overall diameter and/or length. Increasing a tube’s diameter will obscure the site picture of the host gun and inhibit the possibility of holstering a weapon with the silencer still attached to the host gun.

The Osprey is an eccentric silencer, which means that the bore does not run down the middle of the tube. Because of this eccentric design, most of the baffles and internal volume is beneath the centerline of the bore and out of the way of the gun’s sights, thus leaving the shooter the ability to use factory sights with little or no sight or target obstruction. The Osprey has flat side walls and angled edges that mimic many modern combat handgun slides and is just slightly wider than most host pistols. This feature allows the host weapon to be holstered with many popular open bottom holster designs with Osprey attached. The Osprey contains approximately 30% more internal volume than a traditional round tube silencer at the same length, but does so without obscuring the shooter’s sight picture or adding excessive width and length.

Other Benefits

Besides having the best suppression levels available for centerfire handguns, the Osprey silencer family has other benefits and features that are unique to the industry.

Mounting System

Because of its eccentric design, the Osprey must have a way to index to the host gun. Silencerco designed the patent pending cam lever locking system that allows the shooter to time the silencer to any host pistol. To mount, simply thread the Osprey on the muzzle just as you would a traditional silencer with the cam lever in the locked position. When the Osprey shoulders, hand tighten to ensure a tight fit then release the cam lever and rotate the Osprey to the proper orientation. Finally, move the cam lever back to the locked position. The Osprey will return to this index point for subsequent mountings until you change the host pistol or remove the piston assembly for cleaning.

Booster and Accessories

Working in harmony with the patent pending cam lever locking system, the Osprey has a unique booster, or Nielsen device, that allows flawless cycling with all relevant semi-automatic handguns. All of the boosters are the same dimensions on all three Osprey calibers, which means you can interchange the piston portion for different thread specs and subcalibers. For example, you can shoot a 9mm or .40 S&W through a 45Osprey or a 9mm through a 40Osprey. Silencerco also offers a fixed barrel spacer for use on subguns/pistol caliber carbines and host weapons that have fixed barrels.

Nomenclature

Tax stamps are expensive and take a lot of time. Silencerco believes that one tax stamp is enough for your silencer. With this in mind, Silencerco designed the Osprey for quick repairs and placed the serial number on the part least likely to be damaged by baffle strike or other mishaps. Warranty repairs are quick and easy.

Lightweight and Compact

The Osprey is very lightweight and does not greatly affect the balance of the host pistol. The 45Osprey and 40Osprey weigh 11 ounces, and the 9 mm Osprey weighs 9.84 ounces. Many people feel Osprey actually improves the balance of their host firearm. The Osprey also is a handy 8 inches long in the 45Osprey and 40Osprey models and only 7 inches long in 9mm. This design makes them “short” for their performance level.”

Caliber: .45 ACP

Weight: 11.1 oz

Dimensions: 1.3″W × 1.75″H

Length: 8.0625″

Mount: Threads

Sound Reduction: (Dry/Wet): 132.5 dB/123 dB*

*Tested with a HK USP Tactical with Remington UMC 230 Grain Ammunition

Finish

Aluminum Parts: Type III Hard Coat Anodizing

Stainless Steel Parts: Black Oxide

Materials: Core/Caps: 7075 T6 Aluminum

Tube: 6061 T6 Aluminum

Piston/Mounting System: 17-4 Stainless Steel, Heat Treated, Black Oxide

Features: Interchangeable pistons, Unobstructed sight picture, Hearing safe when shot dry, Can be holstered

Patent pending cam lock Mounting system

Lifetime warranty

Thank You,

BMC Tactical / Warrior Steel LLC
2617 Coors Blvd SW, Albuquerque, NM 87121
View the map of our location here

Spikes Tactical BAR Rail

walter — Wed, 25 Jan 2012 15:00:05 +0000

Big Ass Rail- that is what BAR stands for. We have the BAR avialable in 7″ and 10″ lengths

Here is a brief overview provided by Spikes:

The Spike’s Tactical 7″ and 10” BAR Rail is a 1pc free floating quad-rail that’s machined from 6061-T6 Aluminum with a barrel nut machined from 7075-T6 Aluminum and finished in type III Hardcoat Anodizing on the rail and barrel nut. The main benefit of the BAR rail is to those who wish to have a suppressor inside of the rail or for those shooters who have large bear paw hands and who feel that skinnier rails are just too small ( the BAR is about the same circumference as a DD rail with the popular Magpul XTM covers). The 7” BAR rail weighs in at 310 grams (10.93 oz.) and has an ID of 1.79” and the 10” BAR rail weighs in at 406 grams (14.32 oz.) and has an ID of 1.79”.

The BAR rail also features scalloping on the rails that not only saves a little bit more weight but also allows you to run this rail without any rail covers! This sounds like an outlandish claim to those who have had their hands cut up on other quad-rails that have been lovingly called “cheese graters”. The BAR also offers excellent heat ventilation, built in anti-rotation tabs to keep the rail and even the barrel nut from coming loose, and of course; sexy styling.

But wait, there’s more! The BAR has 5 built in QD sockets (sling attachment points), allows for a continuous top rail, it’s compatible with many low profile gas blocks, and it’s made right here in the USA and backed by our LIFETIME WARRANTY!

NOTE: You will need to remove your front sight base and delta ring assembly for installation. The BAR rail system installs with a Standard USGI barrel nut wrench and supplied Torx wrench.

Thank You,

BMC Tactical / Warrior Steel LLC
2617 Coors Blvd SW, Albuquerque, NM 87121
View the map of our location here

Spikes Tactical

walter — Wed, 25 Jan 2012 05:48:41 +0000

We just received over 50 stripped AR15/M4/ST15 receivers from Spikes today plus two different lengths of their BAR quad rail! A quality build begins with a quality lower receiver and Spikes does not disappoint. Their forged receivers feature:

* CNC Machined from a 7075 T6 MIL-H-6088 Forging

* Low Shelf for RDIAS

* Milled Manufacturer Engravings

* Accepts .154″ Diameter Trigger & Hammer Pins

* MIL-A-8625F Type III Class 2 Hardcoat Anodized Finish inside and out

we have Punisher, Calico Jack, and pictogram stripped rifle lowers and several complete SLP pistol lowers as well.

We will post photos and specs tomorrow of the BAR Rails

Thank You,

BMC Tactical / Warrior Steel LLC
2617 Coors Blvd SW, Albuquerque, NM 87121
View the map of our location here

SHOT SHOW 2012

walter — Mon, 23 Jan 2012 02:24:43 +0000

We had an awesome time at the 2012 SHOT SHOW! There are lots of cool new items that we will be bringing in this coming year. We will keep you posted as they become available and are on the way!

Thank You,

BMC Tactical / Warrior Steel LLC
2617 Coors Blvd SW, Albuquerque, NM 87121
View the map of our location here

Primary Weapons Systems Carbines in stock

walter — Thu, 05 Jan 2012 15:42:38 +0000

Hey all,

PWS makes the best for the money gas piston AR/M4 rifle on the market. As a result of that, their rifles are in very high demand and short supply.

We have the following in stock:

MK216FDE- 308 lightweight supremacy with a Flat Dark Earth finish
MK116- 300 blackout chambering, this will be the hottest cartridge for 2012
MK116- 5.56 that shoots as smooth as butter
MK114- 5.56 that brings lightweight compactness to the fight
MK114FDE- 5.56 lightweight in contrasting Flat Dark Earth finish

Thank You,

BMC Tactical / Warrior Steel LLC
2617 Coors Blvd SW, Albuquerque, NM 87121
View the map of our location here

Arrivals for 03 January 2012

walter — Tue, 03 Jan 2012 07:53:55 +0000

Well the new year is here and we are off to an exciting start. SHOT Show is two weeks away, but some manufacturers are already shipping their new offerings for 2012. Kel-Tec is shipping small amounts of the much anticipated KSG shotgun that was debued at last years SHOT, we shall see how it fares. We had a very successful Christmas season and are very thankful to you our customer for it.
Here is what we are expecting today

Ammunition:

Hornady Zombie Max in .45ACP, 9mm, 380ACP, 7.62×39, 40S&W, .308 and .223
PMC bronze in .223, 40S&W
Federal 5.56 100 round value packs
CMMG 300 Blackout ammunition
American Eagle .50BMG

MagPul:

MS3 sling in black
PMag 30 in black and FDE
ASAP plate
RSA
MBUS sights in black
BAD lever
MOE Stocks and Forends in black, FDE
ACS stocks in black and FDE
MOE RVG in all colors
AFG2 in black and FDE
IPhone 4 cases in all colors

Midwest Industires

Factory Mini Draco Rail
MCTAR 13 sling adapter
SS free float rail for AR15/M4 in 7″, 10″ and 12″ lengths

TAPCO:

20 and 30rnd magazines for AK47 variants in black FDE and orange
Grip screw and bushing for AK
Single point plate for AR15
RAZOR break for AK47 variants
Folding stock kit for AK47 variants in FDE

PWS:

MK116 chambered in 5.56
MK114 chambered in 5.56
MK114 chambered in 5.56 Flat Dark Earth Finish
MK116 chambered in 300 blackout!!
MK216 chambered in 7.62×51 FDE finish
CQB 5.56 muzzle device
FSC 5.56 muzzle break
Enhanced buffer tube for collapsible stock

We have more coming in every day, but we will be closed Jan 16-20 for vacation.

Thank you,

BMC Tactical / Warrior Steel LLC
2617 Coors Blvd SW, Albuquerque, NM 87121
View the map of our location here

PWS MK216 FDE

walter — Mon, 02 Jan 2012 04:21:23 +0000

hard to get and a blast to shoot! As the owner of Warrior Steel I can have any rifle I want. When it comes to gas piston rifles, I choose Primary Weapons Systems. PWS offers a full featured rugged light weight gas piston rifle that dollar for dollar cannot be beat.

Here are some specs and features on this Carbine:

Specifications:

Caliber: 7.62×51 NATO

Weight: 8 lbs, 12 oz (3.96 kg)

Overall Length: 34.9″ (88.5 cm)

Barrel Length: 16.1″ (40.9 cm)

Barrel Specs: Stainless Steel, Isonite QPQ Treated, Button Rifled, 1:10 Twist Barrel

Muzzle Velocity: 2600 ft/sec (168 gr FMJ)

Muzzle Energy: 2522 ft/lbs

Features:

Stainless Steel, Isonite QPQ Treated, Button Rifled, 1:10 Twist Barrel

Enhanced Charging Handle

PWS Upper and Lower Receiver

PWS Enhanced Bolt Carrier Group

Isonite QPQ Treated Internals

Magpul XT Rail Panels

Magpul MOE® stock and grip

Magpul MBUS® sights

Magpul PMAG® 20

FSC30

BMC Tactical / Warrior Steel LLC
2617 Coors Blvd SW, Albuquerque, NM 87121
View the map of our location here

Last minute deals from BMC and Warrior Steel

walter — Tue, 13 Dec 2011 19:39:13 +0000

With Christmas only 12 days away, we thought we would offer some last minute deals.

BMC Tactical:

Predator Stocks for Ruger 10/22 10% off
TROY 30rnd battlemags $11.00 each
Aimpoint Micro T-1 with mount $550.00 each
Midwest Industries AK rails 10% off
NEBO flashlights 20% off
25% off in stock 5.11 pants
up to 50% off on select knives

Warrior Steel:

$50.00 off any new in stock rifle
10% off any in stock suppressor
20% off any .22lr handgun in stock
Buy an in stock AK type rifle, get the $50.00 off plus a box of Hornady Z-Max ammo

Sale ends 23 Dec 2011!

BMC Tactical / Warrior Steel LLC
2617 Coors Blvd SW, Albuquerque, NM 87121
View the map of our location here

Gun show this past weekend

walter — Tue, 13 Dec 2011 02:50:46 +0000

We had an awesome time at the gun show. Thanks to all that took the time to visit our tables, without you we would not be able to do what we do. This was the last show for us until March. We have some very exciting plans for the 2012 shows, stay tuned!

Thank you,

Walter

BMC Tactical / Warrior Steel LLC
2617 Coors Blvd SW, Albuquerque, NM 87121
View the map of our location here